2'x4' - 1:10 Scale - Frame ONLY - RC Ramp Jump 40°-60° Made in USA

This is our original ramp design. We just launched a couple new versions for larger cars. This design can work well on 1:8 scale, but high speed hits will move it around without proper support. We now recommend this ramp for 1:10 scale, unless you use it in grass or pack dirt under the ramp deck. 2' long ramp x 4' wide gives a nice transition and is wide enough to actually hit at speed. It folds down to 5" tall and is easy to transport to new spots. Aluminum frame is easy to assemble, start feet hold ramp solid at any angle, leg feet keep it planted. Assembly required - Takes 30-40 min. - Frame bolts together with expanding tube inserts, then clamp deck and use pilot holes in frame to drill and screw the top deck to frame. Ramp Deck - 1 sheet of 1/8" Masonite (hardboard) is cheap and works good for 1:10 scale, get 2 sheets for 1:8 scale. Or upgrade to 1 sheet of 1/8" Lexan (polycarbonate) for a longer lasting deck. Lexan will need to be countersunk for flat head screws to sit flush. Masonite - Search Home Depot for 1/8 in. x 2 ft. x 4 ft. Tempered Hardboard. They have pre-cut 2'x4' sheets for $7. Or a full 4'x8' sheet is only $13 and they will cut it to size for free, which gives you extras. Lexan link - Search Amazon for 1/8" Polycarbonate 24"x48" Do NOT get plexiglass (acrylic) - 24"x48" sheets are available on Amazon for about $50, there are other places to buy from, this is just one example. - Specs - - Folds down to 5" high or 3" if you remove legs. - Weighs 10# with 1 Masonite layer for 1:10 scale, or 15# with 2 layers for 1:8 scale. - Three Settings - 40° is a good long kicker (20-40'), 50° angle high jump launches well over 10' high, 60° angle is great for low to med. speed back flips. - 3/4"x .065 wall 6061 aluminum (also made in USA) frame is easy to assemble with expanding tube inserts - Adjustable legs with 3D printed feet to keep ramp planted - Start feet at base of ramp flip around to hold the start of ramp solid at higher angles - Masonite deck is weather resistant, give it a coat of paint for wet climates. Use smooth side for mostly high speed, or textured side for lower speed stunts.

• **Frame Only** - Supply your own ramp deck, 1/8" Masonite for normal use or 1/8" Lexan for hard bashing. Home Depot has Masonite pre-cut to 2'x4' (24"x48") sizes for only $7 ea. Search Home Depot for 1/8 in. x 2 ft. x 4 ft. Tempered Hardboard... Or step up to 1/8" Lexan (polycarbonate) for about $50 here on Amazon, which is stronger but requires holes to be countersunk for the included flat head screws.
• Best for 1:10 scale, but works up to 1:8 Scale RC cars/trucks - **Assembly Required** Check out our store for smaller RTR (ready to run) ramps and our new Heavy Duty ramps for 1:8 and 1:5 scale trucks. - It takes 30-40min. to assemble frame, drill deck through pilot holes in frame, screw down deck and assemble legs. Lexan will take closer to 60 min. to countersink the holes during assembly.
• For 1:10 scale a single sheet of 1/8" masonite is good, use two layers for 1:8 scale cars. Masonite (hardboard) is nice because it's cheap and easy to assemble, has a textured side for low speed backflips and good weather resistance. If you plan on bashing hard then step up to one sheet of 1/8" lexan. Other plastics will work, but Lexan is the toughest, longest lasting deck. Do *NOT* get pexiglass (acrylic).
• This 2'x4' (24"x48") ramp is the perfect size to transport to your favorite spot and be wide enough to easily hit from any driving angle. Setup only takes a minute and it folds down to 5" tall. Weighs 10-15 lbs. depending on kit.
• Made in USA! -- Aluminum frame (also made in USA) is easy to assemble, start feet hold ramp solid at any angle, leg feet keep it planted. For high speed hits the ramp will need support to hold it in place, packing dirt behind it or adding sand bags will hold it solid.
• Adjustable legs - 40° is a good long kicker (20-40'), 50° angle high jump launches well over 10' high, 60° angle is great for low to med. speed back flips. 1/8 scale will work on larger 1/5 scale RC trucks, but not for full speed hits.
• Read description below for more details. Check out our store for more ramp options or message us with any questions.